Product Categories
How can we help you
You can contact us any way that is convenient for you. We are available 24/7 via email or telephone.
Contact Us
Recently, as September approaches, the pace of autumn is gradually approaching, and it will usher in one autumn rain after another. Although pickup users drive tall and mighty pickup models, the impact of rainy days and the safety hazards of driving in rainy days cannot be ignored. The following are a few small experiences summarized. Be sure to maintain a wide field of vision: turn on the wipers in time after it rains, and turn on the dipped beam, anti-fog lights and position lights. The double flash can not be used, because the turn signal cannot be turned on after the double flash is turned on in rainy days, which will make the driver behind you do not know your driving intention, and it is easy to rear-end. Follow the car in the rain, keep the distance, and brake carefully. Because the ground is slippery in the rain, the grip of the tires will be reduced, and the disc brakes will also enter the water, which will reduce the braking force and increase the braking distance. Do not occupy the road, and the inner lane is reserved for faster vehicles. Although it is necessary to drive slowly in rainy days, do not drive at a turtle speed, especially do not drive at a very low speed with the innermost lane, which is very likely to cause rear-end collision. Slow down and drive carefully: The braking distance on muddy roads can be up to 3 times that of normal roads, so no matter the road conditions are good or bad, the speed of the pickup should be controlled within 40-60km. Especially in high-speed driving, it will cause the wheels to slip and be prone to accidents. Increase the safety distance. Reduce fog generation: When it rains in autumn, the windshield of the pickup is very easy to condense fog and block the sight. If you are not careful, it will cause a catastrophe. At this time, it is necessary to turn on the hot air of the air conditioner and the gear of blowing the windshield to remove the fog in time. Protect your windshield: Apply a water repellant to your windshield and rain will run off quickly. In addition, in rainy days, the rearview mirror is easily stained with rainwater, which makes it difficult to see the vehicles behind, causing traffic accidents. You can install a windshield on the rearview mirror. Frequent dodging is prohibited: In rainy days, someone frequently avoids the water on the road, which can easily cause the vehicles behind to not be able to figure out your driving route and cause rear-end collision.
View MoreAuto parts refer to all parts and components except the car frame, where parts refer to individual components that cannot be separated, and parts refer to the combination of parts that realize a certain action or function. As the upstream of the automobile industry, the auto parts industry is an important part of the auto industry, and it promotes and develops together with the auto industry. Under the background of economic globalization and market integration, the number of motor vehicles has continued to increase in recent years.The demand for auto parts in the aftermarket such as auto repair and auto modification has also expanded, and the performance requirements of auto parts are getting higher and higher. The auto parts industry, as the foundation of the auto industry, is an important factor supporting the sustainable and healthy development of the auto industry.
View MoreAs a key link in the global production and supply chain of auto parts, China now houses almost all the world-leading auto parts manufacturers and is itself a huge exporter of home-made auto tires, glasses and audio products. The scale of China’s auto parts and accessories industry approached RMB1.5 trillion in 2010, with the CAGR of 30% in the past five years. We observed that major competitors in China’s auto parts market post the following development momentum respectively: Multinational auto parts companies: Monopolistic core technologies, intensive localisation and active M&As Local manufactures: Development polarisation, accelerating industry integration and leading companies’ speeding up internationalisation Local entire auto part supporting enterprises: Transition from providing support to the group to seeking independent development Looking forward, after-sale market with its huge needs will become the main growth engine of auto parts market. And with the increase of potential overcapacity risks, the industry will enter an accelerating integration stage.
View MoreSome car owners mainly pay attention to the lubrication system in the maintenance of the engine, and seldom pay attention to the cooling system, but the most common faults of automobile engines, such as piston pulling cylinder, deflagration, cylinder block damage and internal leakage, serious noise, acceleration power drop etc., are caused by abnormal working temperature of automobile engine, excessive pressure, and poor condition of cooling system. When an engine is in good condition with other systems, whether the cooling system can effectively maintain the normal working temperature of the engine fundamentally determines the working condition of the engine. Pay attention to regularly check the efficiency of the cooling system, avoid the failure of the thermostat, adjust the shutters correctly, eliminate the leakage of the machine, keep the coolant temperature in the normal range, prevent the radiator from overheating, etc.
View MoreThe function of the Fuel Pressure Control Valve is to: 1. Adjust the fuel pressure of the fuel supply system to keep the difference between the system oil pressure and the intake manifold pressure constant; 2. Buffer the pressure pulsation generated by the fuel pump and the pressure fluctuation caused by the intermittent fuel injection of the injector. The fuel pressure valve is also called the fuel pressure regulator. The automobile fuel pressure regulator is a part of modern automobiles. It belongs to the fuel supply system of the electronically controlled engine. It is generally installed on the fuel return pipe side of the fuel injector rail. The working principle of the fuel pressure regulator is that when the oil pressure is higher than the standard value, the high-pressure fuel will move up the moving diaphragm, the ball valve will open, and the excess fuel will flow back into the fuel tank through the return pipe; when the pressure is lower than the standard value, the spring The diaphragm will be pressed down to close the ball valve and stop oil return.
View MoreWhen the driver depresses the clutch pedal, the push rod pushes the piston of the master cylinder to increase the oil pressure and enters the wheel pump through the hose, forcing the wheel pump rod to push the release fork and push the release bearing forward; when the driver releases the clutch pedal, The hydraulic pressure is released, the release fork gradually returns to its original position under the action of the return spring, and the clutch is in the engaged state again. There is a radial oblong through hole in the middle of the piston of the clutch master cylinder. The limit screw passes through the oblong hole of the piston, To prevent the piston from rotating, the oil inlet valve is installed into the axial hole at the left end of the piston, and the oil inlet valve seat is inserted into the piston hole through the straight hole on the piston surface.
View MoreThe thermostat automatically adjusts the amount of water entering the radiator according to the temperature of the cooling water, and changes the circulation range of the water to adjust the heat dissipation capacity of the cooling system and ensure that the engine works within a suitable temperature range. The thermostat must be kept in good technical condition, otherwise it will seriously affect the normal operation of the engine. If the main valve of the thermostat is opened too late, it will cause the engine to overheat; if the main valve is opened too early, the engine warm-up time will be prolonged, making the engine temperature too low. All in all, the function of the thermostat is to keep the engine from overcooling. For example, after the engine is working normally, the temperature of the engine may be too low if there is no thermostat when driving in winter. At this time, the engine needs to temporarily stop the water non-circulation to ensure that the engine temperature is not too low.
View MoreSteering knuckle is one of the main parts on the steering axle of a car, which can make the car run stably and transmit the driving direction sensibly. In the driving state of the car, it bears the variable impact load, so it is required to have high strength. Steering transmission shafts are widely used in automobiles. In front-engine rear-wheel or all-wheel drive vehicles, due to the deformation of the elastic suspension, the relative position of the transmission or transfer case output shaft and the axis of the transaxle input shaft often changes, so the cross-shaft steering transmission shaft is generally used. In the steering drive axle, the angle between the inner and outer half shafts changes with the needs of driving, and at this time, the constant speed steering transmission shaft is mostly used. When the rear drive axle is an independent suspension, a steering drive shaft must also be used. The steering knuckle is an important safety part of the automobile. The industry people all over the world attach great importance to its safety characteristics, and fully understand that its safety characteristics play a particularly important role in the processing of the steering knuckle, and should be controlled throughout the manufacturing process. Steering knuckle classification, split type is mainly used for passenger cars (sedans), integral type is mainly used for commercial vehicles (trucks); integral type is divided into independent suspension steering knuckle and non-independent suspension steering knuckle.
View More